Bulk Quantity • Custom Finish
Special Printing • Custom Coating
A half wall runs across the lower part of your tent at about counter height. It frames the booth, hides the clutter under your tables, and gives you extra space for branding - while leaving the top half open so visitors can see in and walk up. To look professional, though, a half wall has to hang straight and tight. Half Wall Hardware is what holds it that way.
The complete set has three pieces: a telescopic support pole and two hex clamps - one straight and one offset. The pole slides through the pole pocket along the top of your half wall, extends to reach from one tent leg to the next, and locks in place with the clamps. When the event is over, the pole collapses short enough to pack in your tent carrying bag with the frame. The pole and clamps are also sold on their own for replacements.
| Complete Set | 3 pieces - support pole + 2 hex clamps |
| Support Pole | Telescopic - extends between tent legs, collapses for storage |
| Hex Clamps | 1 straight clamp and 1 offset clamp |
| Purpose | Holds a half wall straight and secure along its top edge |
| Storage | Fits in the tent carrying bag with the frame |
| Shipping | Ground, 3 Day Select, or 2nd Day Air - pricing includes shipping |
| Tent Legs | For event tents with hex-shaped aluminum legs |
| Half Wall | Not included - wall must have a pole pocket along the top |
| Tent | Not included - Event Tent Frame sold separately |
| Quantity | One set per half wall section |
| Artwork | None required - no file upload needed |
Order the complete set to hang a new half wall, or pick up just the part you need to replace a lost or damaged piece.
The complete 3-piece set: the telescopic pole plus a straight and an offset clamp. Everything you need to hang one half wall section.
The telescopic pole by itself. Ideal if you already own hex clamps and need a replacement or additional pole.
A straight clamp and an offset clamp without the pole. Use them to replace worn or missing clamps.
The hardware is designed around the way event tents are actually used.
Extends to span the distance between two tent legs, then collapses short enough to travel in your tent carrying bag with the frame.
Hex clamps lock the pole to the tent legs without tools, keeping the top edge of the half wall straight and taut.
Hide crates, coolers, and back stock under the tables while keeping the booth open and easy to shop.
Frame the sides of a sponsor booth with a clean, straight wall that adds branding at eye level.
Mark off the team area on the sideline while players and coaches can still see the field.
Create a defined, welcoming space for registration, giveaways, or information tables at community events.
Select the complete set, the support pole only, or the 2 hex clamps only.
Order one set for each side of the tent that will have a half wall.
Choose Ground, 3 Day Select, or 2nd Day Air. Pricing includes shipping.
Slide the pole through the wall pocket, extend it to the legs, and clamp it in place.
The complete set includes three pieces: one telescopic half wall support pole, one straight hex clamp, and one offset hex clamp. Together they hold one half wall section across one side of your event tent. The half wall itself and the tent are not included. If you only need part of the set, the support pole and the pair of hex clamps are each available on their own.
A half wall is a fabric panel that runs across the lower portion of one side of an event tent, usually from the ground up to about counter height. Unlike a full wall, it leaves the upper part of the tent open, so visitors can see into the booth and walk up to your table. Half walls are often printed with a logo or message, adding branding at eye level while hiding boxes and supplies stored under the tables.
The half wall has a sleeve, or pole pocket, sewn along its top edge. Slide the support pole through the pocket, extend the telescopic pole until it reaches the tent legs on either side, and secure it to the legs with the hex clamps. The pole holds the top of the wall straight and taut, so the panel looks clean and does not sag in the middle. No tools are needed, and you can loosen the clamps to adjust the height or level of the wall at any time during the event.
No. This product is the hardware only - the pole and clamps that hold a half wall in place. The half wall panel is sold separately and must have a pole pocket along its top edge for the pole to slide through. If you are not sure whether your existing half wall will work with this hardware, call us and we will help you check before you order.
The hex clamps are made for event tents with hex-shaped aluminum legs - the six-sided leg profile used on many commercial pop-up tent frames. The telescopic pole extends to reach from one tent leg to the next. Before ordering, check the shape of your tent legs. If your tent has round or square legs, or you are unsure, call us with your tent details and we will help you confirm fit.
The set includes one straight clamp and one offset clamp, one for each end of the pole. The two clamp styles let you position the pole cleanly against the tent legs so it sits level and holds the wall straight. Using a clamp at each end locks the pole firmly between the legs and keeps it from sliding or twisting during the event.
Order one complete set for each half wall section you plan to hang. For example, a booth with half walls on the left and right sides needs two sets, and a booth with half walls on three sides needs three sets. Adding a spare set of hex clamps is also a smart way to make sure a lost clamp never keeps a wall from going up.
Unclamp the pole from the tent legs, slide it out of the half wall pocket, and collapse the telescopic pole to its shortest length. It is designed to fit inside your tent carrying bag along with the folded frame, so all of your hardware travels together. Keep the clamps in a small pouch or zip bag inside the carrying bag so they do not get lost between events.
No. Half Wall Hardware is an unprinted product, so there is no file to prepare, no proof to approve, and no upload step. Choose your hardware option, quantity, and shipping method and add it to your cart. Pricing includes shipping, and we ship to all 50 states by Ground, 3 Day Select, or 2nd Day Air.
Our team can help you confirm fit with your tent and half wall, and plan the accessories for your next event.
Contact Us1-800-423-2679Enter your registered email address to reset your password. An email will be sent to your registered email address with a password reset link
If you don’t remember your email address please give us a call during normal business hours 9:00 am – 7:00 pm EST at 1-800-423-2679 or leave a voice mail and we will return your call next business day.
Don’t have an account?
Create a new account